产品详情
类别Category | k型机系列(导柱型)/K Series(tie bar structure) | |||
机型 Model | 65K2×4.2D-A(乐百氏专机) | |||
项目 | Items | 单位 Units | 参数Specification | |
基本参数 Specification | 类别 | Category | / | 单层 1 layer |
制品大容积 | Max. Blow Volume | L | 0.5 | |
适用原料 | Material | / | PE,PP | |
模头坯料数量 | QTY Of Die Head | / | 4 | |
常用模头中心距 | Die Head Distance (Center to Center) | mm | 90 | |
机器净重约 | Net Weight | kg | 5000 | |
机器外形尺寸 | Machine Dimension | m,L×H×W | 3.5x3.3x2.2 | |
模头 Die Head | 模头加热段数 | Die Head Heating Zone | / | 9 |
模头加热功率 | Die Head Heating Power | kW | 5 | |
锁模架系统 Carriage system | 模架数量 | QTY Of Station | / | 2 |
小合模距 | Min Mold Closing Distance | mm | 160 | |
大开模距 | Max Mold Openning Distance | mm | 310 | |
模板尺寸 | Effective Dimension Of Mold Plate | (mm,W×H) | W380×H270 | |
摆架行程 | Carriage Stroke | (mm) | 500 | |
锁模力 | Clamping Force | kN | 27 | |
挤出系统 Extruder Unit | 螺杆直径 | Extruder Diameter | mm | 65 |
螺杆长径比 | Extruder Length/Diameter Ratio | L/D | 24 | |
螺杆转速 | Extruder Rotating Speed | r/min | 20-67 | |
大塑化能力 | Max Extrusion Capacity | kg/h | 60 | |
挤出电机额定功率 | Extruder Motor Rated Power | kW | 15 | |
机筒加热段数 | Barrel Heating Zone | / | 3 | |
机筒加热功率 | Barrel Heating Power | kW | 7 | |
冷却风机功率 | Cooling Fan Power | kW | 0.12 | |
动力系统 Power Unit | 油泵电机额定功率 | Oil Pump Motor Rated Power | kW | 7.5 |
液压系统额定工作压力 | Hydraulic System Rated Wong Pressure | Mpa | 14 | |
气动系统额定工作压力 | Pneumatic System Rated Wong Pressure | Mpa | 0.8 | |
水冷系统额定工作压力 | Cooling System Rated Wong Pressure | Mpa | 0.4 | |
通用制品耗气量(压缩后) | Universal product air consumption(compressed) | m³/h | 21 | |
热切刀变压器功率 | Hot Cutter Power | kW | 2 | |
装机总功率I | Total Installed Power | kW | 36.62 | |
备注 Remarks | 液压油牌号/油箱容积 | Hydraulic oil NO. / tank volume | L | 46#/160L |
冷水机选型(风冷/水冷) | Chiller recommend (air-cooled/water-cooled) | hp | 5 | |
空压机选型(加储气罐) | Air compressor recommend (Add gas storage tank) | hp | 10 | |
备注/Remarks: | 以上机型 Model均可叠加100点壁厚控制系统,叠加后改变的参数如下/All the machines above can be optionally equipped with 100 points parison cool system,parameters would be changed as below: | |||
叠加壁厚控制后 After with 100 points parison cool | 机型 Model | Model | / | 65K+S2X6.2D-A |
壁厚油泵电机额定功率 | Parison Servo Motor Rated Power | kW | 5.5 | |
装机总功率II | Total Installed Power | kW | 42.12 | |
锁模板示意图 Clamping plate | ||||
备注: 1、各机型的加热功率与模头配置有关,因模头配置不同,可能出现加热功率稍有差异的情况。 2、本参数表仅供参考,实际机型参数可能会有所调整。 | ||||
Note: 1. The heating power of each model is related to the configuration of the die head. Due to the different configuration of the die head, there may be a slight difference in heating power. 2. This parameter list is for reference only, and the actual model parameters may be adjusted. |